RPG Forums

Go Back   RPG Forums > Role Playing Game Section > Morrow Project/ Project Phoenix Forum

Reply
 
Thread Tools Search this Thread Display Modes
  #211  
Old 05-29-2017, 03:39 PM
ArmySGT.'s Avatar
ArmySGT. ArmySGT. is offline
Internet Intellectual
 
Join Date: Jun 2011
Location: Colorado
Posts: 2,412
Default

Airwolf

Reply With Quote
  #212  
Old 05-29-2017, 08:36 PM
kato13's Avatar
kato13 kato13 is online now
Administrator
 
Join Date: May 2007
Location: Chicago, Il USA
Posts: 3,647
Send a message via ICQ to kato13
Default

Quote:
Originally Posted by ArmySGT. View Post
Airwolf
I loved Airwolf. I even turned in 20 or so sheets of extra credit in my Drafting class of the schematic drawings from the opening credits. I painstakingly drew them from paused images.

Here are some modern thoughts on how Airwolf might look today. (From Deviant Art)
Attached Images
    
Reply With Quote
  #213  
Old 07-01-2017, 02:56 PM
tsofian tsofian is offline
Registered User
 
Join Date: Aug 2015
Posts: 342
Default

Adding mass is easy. That is what depleted uranium is all about and it used to be used for the purpose of balancing aircraft regularly. Not sure if it still is but during the 80s it was a pretty common practice. Of course the missing mass could be used for something mission related like armor or such. The issues with engines further out can be dealt with by moving the electric motors or assuming that the Project has better electric motors.

Quote:
Originally Posted by mmartin798 View Post
This is where things can get a little off. There is an electric motor that can be stacked to provide 300 kW continuous to the rotor in place of the C20R. It would have a length of 540 mm, diameter of about 245 mm and a total mass of 129 kg. Add in the (3rd edition) manportable 20MW reactor at 15kg and you have 145 kg give or take fully fueled. The non-fusion MD500/520 carries 183kg of fuel in addition to the 78.5 kg of the engine for about 260 kg. The two fuel cells of the MD500 are under the floor more or less centered around the rotor. Assuming the reactor can fit inside the space as the fuel cells, we will still have to add more weights to the front of the MD500 for load and balance.

This is doable in the MD500 case, but the electric motors will tend to be heavier and smaller than the ones they replace and the reactor, assuming 20MW sufficient, will be lighter than the fuel. This will be a problem with planes with engines mounted far out on the wings. This will increase the moment of inertia and will impact handling.

So the takeaway is that center line drive trains should be easy to convert with little impact to the flight characteristics. Anything with the engine further out on the wing and you will have some slower turn and roll.
Reply With Quote
  #214  
Old 07-01-2017, 03:18 PM
tsofian tsofian is offline
Registered User
 
Join Date: Aug 2015
Posts: 342
Default

Adding mass is easy. That is what depleted uranium is all about and it used to be used for the purpose of balancing aircraft regularly. Not sure if it still is but during the 80s it was a pretty common practice. Of course the missing mass could be used for something mission related like armor or such. The issues with engines further out can be dealt with by moving the electric motors or assuming that the Project has better electric motors.

Quote:
Originally Posted by mmartin798 View Post
This is where things can get a little off. There is an electric motor that can be stacked to provide 300 kW continuous to the rotor in place of the C20R. It would have a length of 540 mm, diameter of about 245 mm and a total mass of 129 kg. Add in the (3rd edition) manportable 20MW reactor at 15kg and you have 145 kg give or take fully fueled. The non-fusion MD500/520 carries 183kg of fuel in addition to the 78.5 kg of the engine for about 260 kg. The two fuel cells of the MD500 are under the floor more or less centered around the rotor. Assuming the reactor can fit inside the space as the fuel cells, we will still have to add more weights to the front of the MD500 for load and balance.

This is doable in the MD500 case, but the electric motors will tend to be heavier and smaller than the ones they replace and the reactor, assuming 20MW sufficient, will be lighter than the fuel. This will be a problem with planes with engines mounted far out on the wings. This will increase the moment of inertia and will impact handling.

So the takeaway is that center line drive trains should be easy to convert with little impact to the flight characteristics. Anything with the engine further out on the wing and you will have some slower turn and roll.
Reply With Quote
  #215  
Old 08-19-2017, 10:02 AM
ArmySGT.'s Avatar
ArmySGT. ArmySGT. is offline
Internet Intellectual
 
Join Date: Jun 2011
Location: Colorado
Posts: 2,412
Default

AT-6 Wolvernine COIN / CAS war plane.

<script type="text/javascript" src="//video.foxnews.com/v/embed.js?id=5544203479001&w=466&h=263"></script><noscript>Watch the latest video at <a href="//video.foxnews.com">video.foxnews.com</a></noscript>
Reply With Quote
  #216  
Old 09-28-2017, 04:54 PM
ArmySGT.'s Avatar
ArmySGT. ArmySGT. is offline
Internet Intellectual
 
Join Date: Jun 2011
Location: Colorado
Posts: 2,412
Default

This is sooooooooo Morrow Industries subsidiary.

Flugwerk

A German company is building FW-190 parts kits to repair or rebuild....even in some cases, a new airframe.


FW-190 and Buker 131B

Something to think about for Atlantis Project.
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 04:46 PM.


Powered by vBulletin® Version 3.8.6
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.